Filetype
Context: This paper analyses a sub-contractor specification in the mobile handset domain. Objective: The objective is to understand how quality requirements are specified and which types of requirements exist in a requirements specification from industry. Method: The case study is performed in the mobile handset domain, where a requirements specification was analyzed by categorizing and characteri
Geometry-based stochastic channel models (GSCMs) are extended to support multi-link simulations by applying the concept of common clusters. This novel approach aims to control the correlation between different links, inter-link correlation, by adjusting the amount of power simultaneously propagating via the same clusters in the different links. The behavior of common clusters is analyzed based on
This paper presents two class-C CMOS VCOs with a dynamic bias of the core transistors, which maximizes the oscillation amplitude without compromising the robustness of the oscillation start-up, thereby breaking the most severe trade-off in the original class-C topology. An analysis of several different oscillators, starting with the common class-B architecture and arriving to the proposed class-C
The COST 2100 channel model has introduced the concept of common clusters to model multi-link MIMO characteristics. In this paper, a ray launching tool is used to analyze multi-ink propagation properties in an outdoor scenario at 300 MHz. It is shown that in a multi-link propagation scenario there are shared scatterers among the different links, which reflects the physical existence of common clus
This paper presents a low band antenna impedance tuner in 130nm CMOS-SOI technology. It consists of three digitally controlled switched capacitor banks and two off-chip inductors and is intended for use in terminals supporting modern cellular standards like WCDMA and LTE. By using a negative gate bias in the off state, linearity can be improved and maintained. Measurements show an OIP3 exceeding +
This paper presents the co-design of a class-D digitally-controlled oscillator (DCO) and a low-dropout voltage regulator (LDO) generating the supply voltage for the DCO. Despite the high intrinsic supply pushing of the class-D oscillator topology, the LDO noise has only a very marginal impact on the DCO phase noise. The class-D DCO and LDO have been integrated in a 65nm CMOS process without any th
Human beings make errors and that is nothing that we can avoid completely. We can however lower the risk of people doing wrong in situations where, for example, medical devices are used. The overall objective of the research presented in this paper is to investigate how usability testing can contribute to software risk management process in the medical device domain. Experience has been collected
In radio communications, a set of links that can transmit in parallel with a tolerable interference is called a compatible set. Finding a compatible set with maximum weighted revenue of the parallel transmissions is an important subproblem in wireless network management. For the subproblem, there are two basic approaches to express the signal to interference plus noise ratio (SINR) within integer
Multi-antenna design in compact mobile handsets at frequency bands below 1 GHz is very challenging, since severe mutual coupling is commonly induced by simultaneous excitation of the chassis’ fundamental dipole mode by more than one antenna element. To address this problem, a novel multi-antenna design approach is proposed herein to obtain efficient and uncorrelated antennas. By manipulating the c
A closely-packed ultrawideband (UWB) multiple- input multiple-output (MIMO)/diversity antenna (of two elements) with a size of 25 mm by 40 mm is proposed for USB dongle applications. Wideband isolation can be achieved through the different patterns and polarizations of the two antenna elements. Moreover, the slot that is formed between the monopole and the ground plane of the half slot antenna is
In telecommunication networks based on the current Ethernet technology, routing of traffic demands is based on multiple spanning trees: the network operator configures different routing spanning trees and assigns each demand to be routed in one of the selected spanning trees. A major optimization issue in this solution is the combined determination of (i) a set of appropriate spanning trees, and (
This paper presents the VLSI design of an energy-efficient, high-throughput soft-input soft-output signal detector for iterative multiple-input multiple-output (MIMO) receiver. The detector is evolved from our previously developed imbalanced fixed complexity sphere decoder and adopts several new algorithm-level techniques to exploit the available a priori information of transmitted bits. More spec
This paper describes a hardware efficient linear pre-coder for Massive MIMO Base Stations (BSs) comprising a very large number of antennas, say, in the order of 100s, serving multiple users simultaneously. To avoid hardware demanding direct matrix inversions required for the Zero-Forcing (ZF) pre-coder, we use low complexity Neumann series based approximations. Furthermore, we propose a method to
Vehicles in the future are anticipated to have the ability to communicate and exchange useful information in order to avoid collisions. However, for this cooperation to be possible, all vehicles will have to be equipped with compatible wireless modules, based on, e.g. IEEE 802.11p (used in ITS-G5 or WAVE), which implements intelligent transport systems operating in the 5 GHz frequency band. During
Weak alignment of requirements engineering (RE) with verification and validation (VV) may lead to problems in delivering the required products in time with the right quality. For example, weak communication of requirements changes to testers may result in lack of verification of new requirements and incorrect verification of old invalid requirements, leading to software quality problems, wasted ef
Pathloss is typically modeled using a log-distance power law with a large-scale fading term that is log-normal. However, the received signal is affected by the dynamic range and noise floor of the measurement system used to sound the channel, which can cause measurement samples to be truncated or censored. If the information about the censored samples is not included in the estimation method, as i
